臥式化糞池模具設計樣式與特點是以整體式結構為出發點，在臥式化糞池模具加工過程中，每種模具的大小是不固定的，而且直徑、壁厚、高度等都是按照具體要求定制的，臥式化糞池不同于立式化糞池，一般壁厚多在10厘米以下。臥式化糞池模具設計樣式與特點深受市場的好評，混凝土化糞池模具這幾年一直使用的是鋼模具，The design style and characteristics of horizontal septic tank mold are based on the integral structure. In the process of horizontal septic tank mold processing, the size of each mold is not fixed, and the diameter, wall thickness and height are customized according to specific requirements. Horizontal septic tank is different from vertical septic tank, and the general wall thickness is less than 10cm. The design style and characteristics of horizontal septic tank mould are highly praised by the market. The concrete septic tank mould has been using steel mould in recent years,
化糞池屬于大型設備，有的生產難以滿足需要，所以分成三段預制，這樣做的目的是減小生產的難度，使生產制作的時候更加便捷，省時省力，完成效率生產。混凝土化糞池模具采用的鋼板多達六個厚，筋板也是八個厚的，這樣的厚度是為了保證模具的不變形，我們知道，模具一旦變形就很難在進行使用，而且修理的費用很高，變形嚴重的直接報廢，所以在使用化糞池模具的時候選擇好模具鋼材的質量和厚度是很重要的。生產出的化糞池一般壁厚在十五公分左右，這個厚度既可以保證生產的需要，在使用過程中，收到水流的沖擊也不會滲漏，而且在制作上減小了難度。隨著科技的不斷發展，我們從三格化糞池的使有發展到了臥式化糞池的使用，是市場要求和廠家不算創新的結果，相信在將來，我們會制造出質量更好使用更方便的化糞池。
Septic tanks are large-scale equipment. Some production is difficult to meet the needs, so they are prefabricated in three sections. The purpose of this is to reduce the difficulty of production, make production more convenient, save time and labor, and complete efficient production. The concrete septic tank mold adopts up to six thick steel plates and eight thick rib plates. This thickness is to ensure that the mold does not deform. We know that once the mold deforms, it is difficult to use it, and the repair cost is very high. If the deformation is serious, it will be directly scrapped, Therefore, it is very important to select the quality and thickness of mold steel when using septic tank mold. Generally, the wall thickness of the produced septic tank is about 15 cm, which can not only meet the needs of production, but also will not leak after receiving the impact of water flow in the process of use, but also reduce the difficulty in production. With the continuous development of science and technology, we have developed from the use of three compartment septic tanks to the use of horizontal septic tanks, which is the result of market requirements and manufacturers' non innovation. I believe that in the future, we will manufacture septic tanks with better quality and more convenient use.
